Mine are the same. 4 - LW. C Taper 130 X
I was told once that wedges that you're going to full swing should have same shafts as other irons. Makes sense.
Either heavier or same weight. Lighter would be a no-no. Sometime stock vokeys would be too light for whatever reason. I think they'd put S200s in there, call it "wedge flex", and say no could tell the difference. But I could. Now I have the heaviest weight shaft i could find that also matches the overall bend profile of my irons.
X100 in the 54 degree since I rarely use it inside 100 yards. S400 in the 60 for best feel and versatility on all shots inside 100 yards.
Taylormade M5 (9) - Tensei Pro Orange 60
Taylormade M3 T3 (14) - Tensei Pro Orange 70
Taylormade M3 5W (19) - Tensei Pro Orange 80
Srixon Z945 3-PW - DG Tour X100
Taylormade TP EF 54.11 - DG Tour X100
Taylormade TP EF 60 ATV - DG Tour S400
Scotty Cameron Studio Style NP2
Heavier shafts in my wedges. Don't know why it works for me but it does. Steelfiber i95's in my irons, s400 in my wedges.
Modus 105 S in 4-P....TI S400 50 & 56....Modus 125 S in the 60
I absolutely love the feel and performance of the TI s400 wish I had gone that route awhile ago. So stable. The modus 125 S was one I had laying around. It happened to work perfect in the 60
I like all of the set irons/wedges (through GW or SW for me) to have the same shaft.
For the highest lofted wedge, I've had anything from an r-flex 6-iron shaft to an X100. The feel is different but I'm not sure it makes much of a difference in the actual shot on these partial swings.
I play the same shaft in all of my 'full shot' wedges, but a wedge-specific shaft from the same manufacturer in the lob wedge.
So Modus 105 in 4-GW/SW and Modus 105 Wedge (111g actual) in the 60 degree lob.
I think heavier is better for choke down touch shots etc. 110 in irons, and 125 in wedges for me.
Same for me in all but the 58*. I go heavier in the 58 and normally a flex softer or half flex. I like all my fuller swing shafts to match. To me the lob 58 in my case is a club all it’s own. It needs to feel good for 25 shots rather than 3-4.
CALLAWAY EPIC FLASH SZ 9 EV BLACK 75 6.5 44 1/4”
CALLAWAY EPIC FLASH SZ 15 MATRIX HD9 STRONG 41.5”
WILSON FG5 TOUR 17* RIP PHENOM 100 S
SRIXON Z FORGED 3-PW CATALYST 100 6.5
CLEVELAND RTX4 50* CATALYST 100 6.0
CLEVELAND RTX4 54* CATALYST 100 6.0
CLEVELAND RTX4 58* MODUS 120X
SEEMORE mFGP20 PLATINUM 38”
I'm ctaper x from wedges through irons, but they're all 0.5 inches short and lately with my wedges I've had issues where I thin or chunk shots when gripping down on my wedges, is this a shaft issue? I may go with some s400's at standard length. Is this a good idea?
I prefer a little heavier. KBS C Taper 120 in irons and KBS tour 125 in wedges. Works for me.
I use ascending weight Steelfiber Players Spec shafts in my MOI matched irons. I have Nunchuk Xi shafts with a higher MOI/swing weight in my wedges. But that's probably just because I got the Nunchuk's used to experiment with and I found they work well in my wedges.
DG s300 in irons and DG s400 in wedges, without the fancy TI label,🙊 yet sorted precisely for headweights used, so I'm good with that👍😁
Have used both of these shaft variants in many different irons and wedges, comfortable and it works well for me, so no need to change.
Love the same feel across all swings so playing PX LZ’s 6.0 across all, can’t go wrong really
Like a lot of others on here I use X100 4-P, and S400 in 50, 54, and 58.
R400 Sensicore in my OG 588 60° is a joy that lasts forever.
I built my last few sets with the same shafts going all the way through my lob wedge, with a consistent swingweight progression. I think it helps consistency in feel.
But if I used really light iron shafts, I think I would have to use something heavier in the 54*+ wedges. They need some weight so they move through the grass well, and feel right with slower pitch and chip swings. High swingweight with light shafts doesn't feel the same as heavier overall weight.