Cobra adapter conversion chart?

[asumnerdawg]

Anyone have an updated chart that lists f8+? I have a 661 speeder out of an f8+ that I want to put into an ltd pro. Thanks in advance

[Lord Helmet]

Havent seen one. Give Cobra a call and they should be able to assist. G luck!

[jar59]

The lowest loft of the F8+ is 8 degrees. That loft setting will play at 7 degrees on the LTD Pro.

 

Here are the other settings if you do not have them:

 

F8+ to LTD PRO

 

8.5 equals 7.5 Flat

8.5 Draw equals 7.5

9.5 equals 8.5 F

9.5 D equals 8.5

10.5 equals 9.5 F

10.5 D equals 9.5

11 equals 10

 

If you still need the conversion and this doesn’t make sense, let me know and I will try again.

[JSkinner]

I am trying to figure this out as well but I have the opposite situation. I have a shaft from an Ltd pro using it in a F8+. I called cobra and they don’t know.

[jar59]

You can still use this list. Just start with the F8+ number you want to have and find it in the left column. Then adjust the club to the paired setting on the right. Please post again if you struggle with this information. What F8+ setting do you want at this time?

[Jack Daniels]

Related question, is the adapter from a Bio Cell + the same as what would be in a F8+?

[jar59]

Yes, the F8+ driver has the same loft settings as the Bio Cell +. The wrench is different but the loft settings are the same.

[Jack Daniels]

Yes, the F8+ driver has the same loft settings as the Bio Cell +. The wrench is different but the loft settings are the same.

 

What do you mean the wrench is different? Like a different size?

[jar59]

The Cobra wrench and screw head slot (?) changed starting with the F6 club heads. The wrench for the Bio Cell head will not be able to turn the screw of the F8+, it is to small. You can get a new wrench from Cobra or use a wrench from Titleist or TaylorMade on the F8+, but there may be some risk with non-Cobra wrenches.

[Mob]

anyone have a Cobra adapter chart going from left handed to right handed?

[ChaosTheory]

So scr3w is a banned word? LOL!

[ChaosTheory]

> @Mob said:

> anyone have a Cobra adapter chart going from left handed to right handed?

The normal and draw "sides" are the same.

The loft number changes move in the opposite direction.

Say you have a LH head of 10.5 degrees, and a shaft from a RH 11.5 head.

The 11.5 setting will give you 10.5, because those are the middle numbers for each component. Set the shaft adapter in the middle, and you'll get whatever the head's loft actually is. With me so far? Good.

Want to change loft? If you want to move the loft lower, change the adapter setting HIGHER. So you want to go to 9.5 real loft, you'll set the 11.5 adapter to 12.5. OK?

If you want Draw, which is upright, just use the loft settings that have the D mark. Those are upright no matter if you are using the opposite hand shaft.

 

Hope this helps!!! Ask if you need clarification.

 

 

[Mob]

> @Snowman9000 said:

> > @Mob said:

> > anyone have a Cobra adapter chart going from left handed to right handed?

> The normal and draw "sides" are the same.

> The loft number changes move in the opposite direction.

> Say you have a LH head of 10.5 degrees, and a shaft from a RH 11.5 head.

> The 11.5 setting will give you 10.5, because those are the middle numbers for each component. Set the shaft adapter in the middle, and you'll get whatever the head's loft actually is. With me so far? Good.

> Want to change loft? If you want to move the loft lower, change the adapter setting HIGHER. So you want to go to 9.5 real loft, you'll set the 11.5 adapter to 12.5. OK?

> If you want Draw, which is upright, just use the loft settings that have the D mark. Those are upright no matter if you are using the opposite hand shaft.

>

> Hope this helps!!! Ask if you need clarification.

>

>

 

Thanks, so numbers go in opposite direction but draw doesn't change, correct?

[ChaosTheory]

And this is much easier for RH shaft in RH hand. Just figure out what the middle loft is on the shaft, and what the loft is of the head.

So if you have a 10.5 head and the middle loft on the shaft is 11.5, just subtract 1 from every number on the adapter. That's it, you're done.

 

[ChaosTheory]

> @Mob said:

> > @Snowman9000 said:

> > > @Mob said:

> > > anyone have a Cobra adapter chart going from left handed to right handed?

> > The normal and draw "sides" are the same.

> > The loft number changes move in the opposite direction.

> > Say you have a LH head of 10.5 degrees, and a shaft from a RH 11.5 head.

> > The 11.5 setting will give you 10.5, because those are the middle numbers for each component. Set the shaft adapter in the middle, and you'll get whatever the head's loft actually is. With me so far? Good.

> > Want to change loft? If you want to move the loft lower, change the adapter setting HIGHER. So you want to go to 9.5 real loft, you'll set the 11.5 adapter to 12.5. OK?

> > If you want Draw, which is upright, just use the loft settings that have the D mark. Those are upright no matter if you are using the opposite hand shaft.

> >

> > Hope this helps!!! Ask if you need clarification.

> >

> >

>

> Thanks, so numbers go in opposite direction but draw doesn't change, correct?

 

Correct.

And if the neutral/middle loft on the adapter is different than your head's loft, you'll have to adjust for that too. But mainly remember, loft down with the adapter to loft up the head, and v.v.

[Mob]

> @Snowman9000 said:

> > @Mob said:

> > > @Snowman9000 said:

> > > > @Mob said:

> > > > anyone have a Cobra adapter chart going from left handed to right handed?

> > > The normal and draw "sides" are the same.

> > > The loft number changes move in the opposite direction.

> > > Say you have a LH head of 10.5 degrees, and a shaft from a RH 11.5 head.

> > > The 11.5 setting will give you 10.5, because those are the middle numbers for each component. Set the shaft adapter in the middle, and you'll get whatever the head's loft actually is. With me so far? Good.

> > > Want to change loft? If you want to move the loft lower, change the adapter setting HIGHER. So you want to go to 9.5 real loft, you'll set the 11.5 adapter to 12.5. OK?

> > > If you want Draw, which is upright, just use the loft settings that have the D mark. Those are upright no matter if you are using the opposite hand shaft.

> > >

> > > Hope this helps!!! Ask if you need clarification.

> > >

> > >

> >

> > Thanks, so numbers go in opposite direction but draw doesn't change, correct?

>

> Correct.

> And if the neutral/middle loft on the adapter is different than your head's loft, you'll have to adjust for that too. But mainly remember, loft down with the adapter to loft up the head, and v.v.

 

Thank you.

[ChaosTheory]

You can see why they finally changed to +1, -1 etc. I'm sure they were trying to make it super simple in the beginning, but now it's a nightmare.

[jbrunk]

@Mob maybe this will help.

 

[markc1]