Scotty stamps question.

[Matillac]

Hi all,

While filling out the form on the custom shop website I noticed in the section to add stamping that it says the peace sign, scotty dog, skull etc. Are reserved for Tour Only putters.

Has this always been the case?

So would that mean that this is a Tour only putter even though it doesn't have a CT stamp?

 

[976-Evil]

I was under the impression that they don't stamp on the neck like that anymore, nor do they do extreme toe or heel stamping so that was probably done years ago before that rule and apparently the tour only rule went into effect.

[benno_r]

Those skulls look more like engravings, not stamps.

[Matillac]

From what I understand it's from around 2007 to 2008.

So basically just an older custom shop Newport beach?

[mjbfyb]

> @Matillac said:

> From what I understand it's from around 2007 to 2008.

> So basically just an older custom shop Newport beach?

 

I don’t think that is a custom shop job. They’re not going to sand the sole and face like that, and wouldn’t touch it if you sent it in already sanded down.

 

[Luke.Sutton]

Non-custom shop refinish.

[Matillac]

How can you tell it is not a custom shop job?

[tangojay]

IMHO from looking at it, I don't think it's even a Cameron, looking at the following:

 

The "Titleist stamping" on face does not look right, the angle and the "st" does not seem right

The bumper engraving looks off

Of course the most obvious, the sole, this is a Studio Stainless Steel model, it would have been engraved on bottom

The engraving on sole, three different sizes,,,

**_CANNOT_** be 2007 or 2008, according to the Cameron archive site,,,, https://www.scottycameron.com/putter-archive/ ,,,,,, in 2005 the Studio Style with the insert had been introduced

 

Where did you get this ?

[Matillac]

So someone went crazy stamping (or engraving) different sized skulls/jesters and doing an incredible paint-fill on a basic Newport beach? I understand if it was just done as a custom job because that's what the original person wanted but don't understand why someone would spend the time and money to do this otherwise.

[mjbfyb]

> @tangojay said:

> IMHO from looking at it, I don't think it's even a Cameron, looking at the following:

>

> The "Titleist stamping" on face does not look right, the angle and the "st" does not seem right

> The bumper engraving looks off

> Of course the most obvious, the sole, this is a Studio Stainless Steel model, it would have been engraved on bottom

> The engraving on sole, three different sizes,,,

>

> Where did you get this ?

 

I think it’s legit but has been sanded down. As far as I know, this model hasn’t been faked. They fakes started with the Studio Style line.

 

 

[tangojay]

> @Matillac said:

> So someone went crazy stamping (or engraving) different sized skulls/jesters and doing an incredible paint-fill on a basic Newport beach? I understand if it was just done as a custom job because that's what the original person wanted but don't understand why someone would spend the time and money to do this otherwise.

 

Reason ? $$$$$ there is websites where you can get counterfeit Cameron Industrial covers for $20, real ones go for over $100, they also have Cameron counterfeit putters,,,,

[tangojay]

> @mjbfyb said:

> > @tangojay said:

> > IMHO from looking at it, I don't think it's even a Cameron, looking at the following:

> >

> > The "Titleist stamping" on face does not look right, the angle and the "st" does not seem right

> > The bumper engraving looks off

> > Of course the most obvious, the sole, this is a Studio Stainless Steel model, it would have been engraved on bottom

> > The engraving on sole, three different sizes,,,

> >

> > Where did you get this ?

>

> I think it’s legit but has been sanded down. As far as I know, this model hasn’t been faked. They fakes started with the Studio Style line.

>

>

 

If its legit, what's the weight now ?!?!?!?!

[Matillac]

> @tangojay said:

> > @Matillac said:

> > So someone went crazy stamping (or engraving) different sized skulls/jesters and doing an incredible paint-fill on a basic Newport beach? I understand if it was just done as a custom job because that's what the original person wanted but don't understand why someone would spend the time and money to do this otherwise.

>

> Reason ? $$$$$ there is websites where you can get counterfeit Cameron Industrial covers for $20, real ones go for over $100, they also have Cameron counterfeit putters,,,,

 

I understand, but there's no CT stamp so it's still just a Newport beach worth only a couple hundred bucks at best so why? The whole because $$$$$ doesn't make sense.

My original question in this thread has gone off track but maybe not in a bad way. I'd still like to hear input from others much more knowledgeable on this than I am! I can take and post more pics from different angles if that will help.

[tangojay]

> @Matillac said:

> > @tangojay said:

> > > @Matillac said:

> > > So someone went crazy stamping (or engraving) different sized skulls/jesters and doing an incredible paint-fill on a basic Newport beach? I understand if it was just done as a custom job because that's what the original person wanted but don't understand why someone would spend the time and money to do this otherwise.

> >

> > Reason ? $$$$$ there is websites where you can get counterfeit Cameron Industrial covers for $20, real ones go for over $100, they also have Cameron counterfeit putters,,,,

>

> I understand, but there's no CT stamp so it's still just a Newport beach worth only a couple hundred bucks at best so why? The whole because $$$$$ doesn't make sense.

> My original question in this thread has gone off track but maybe not in a bad way. I'd still like to hear input from others much more knowledgeable on this than I am! I can take and post more pics from different angles if that will help.

 

Well, you can always send it for a C.O.A and remove **ALL** doubts. Who knows, you may have something rare.

[Matillac]

That's what I'm thinking as I'm sending another in for a new grip and COA anyway. Two birds, one stone eh?

I'll let ya'll know what they say when I get it back.

 

 

[SubaruWRX]

> @tangojay said:

> > @Matillac said:

> > > @tangojay said:

> > > > @Matillac said:

> > > > So someone went crazy stamping (or engraving) different sized skulls/jesters and doing an incredible paint-fill on a basic Newport beach? I understand if it was just done as a custom job because that's what the original person wanted but don't understand why someone would spend the time and money to do this otherwise.

> > >

> > > Reason ? $$$$$ there is websites where you can get counterfeit Cameron Industrial covers for $20, real ones go for over $100, they also have Cameron counterfeit putters,,,,

> >

> > I understand, but there's no CT stamp so it's still just a Newport beach worth only a couple hundred bucks at best so why? The whole because $$$$$ doesn't make sense.

> > My original question in this thread has gone off track but maybe not in a bad way. I'd still like to hear input from others much more knowledgeable on this than I am! I can take and post more pics from different angles if that will help.

>

> Well, you can always send it for a C.O.A and remove **ALL** doubts. Who knows, you may have something rare.

 

Or you end up with a COA that states it’s a Cameron OTR putter with aftermarket stamping...

[Matillac]

That is also a possibility, but it"ll be an OTR with a Cert! Lol

[Matillac]

 

[Matillac]

And the cover it came with

[Matillac]

 

It glows in the dark!

 

[aenemated]

That looks freakin AWESOME.

[BYK]

Yeah, that is absolutely an OTR that has been heavily modified with aftermarket work.

if you send for a COA, it'll get a C and you've spent a lot of money to do so

If you like it, just game it.

[Skhacker]

The headcover is worth way more than the putter. Cover is a limited Halloween release. Putter is a heavily modified(not by the custom shop) otr Newport Beach. Likely going to be very light now too after being ground and sanded.

[Medson]

Man, that’s some heavy after market job. I’d game the heck out of it.

[SubaruWRX]

I like everything about it except for GUS’s initials on the face. It’s awesome. Game it!

[cardia10]

This one is easy and isn't worth sending in. Like others have said, it is an OTR with aftermarket work. Anyone can get a stamp made and someone went crazy with some stamps. If you like it, it is a cool gamer and I'm sure there will be plenty that like it. With the top line as a skull, I wouldn't touch it for $50 but someone would. Probably weighs in the 320 or less neighborhood with the sole shaved.

[tangojay]

Just curious if OP sent it in ,,,,,,,,,,,,,,,,,,,,,,,,

[BYK]

would be a waste of his money to do that unfortunately

hope he didn't