Jump to content

Simple Diy Shaft puller


Fgav2402
 Share

Recommended Posts

Simple Diy Shaft puller I made using a car brake spreader tool and a simple wooden clamp.

 

Brake spreader bought on amazon,

 

drilled a 10mm hole through the brake spreader and cut a groove down to meet the hole. The clamp is very basic, just 2 pieces of wood with bolts going through.

I use 2 rubber shaft clamps and a screw with washers on the adapter when pulling.

There are two washers in the spreader tool that I added to make it more stable, they are pointed out in the pictures.

I also use an extracting plate if pulling hybrids or fixed hosel woods.

Iv been pulling shafts with this for a while and I'm getting straight pulls and haven't had a tip failure.

IMG_20210528_142828.jpg

IMG_20210528_142855.jpg

IMG_20210528_142913.jpg

IMG_20210528_142933.jpg

IMG_20210129_130319.jpg

IMG_20210528_210240.jpg

Edited by Fgav2402
  • Like 2
  • Thanks 2
Link to comment
Share on other sites

Awesome! I’m getting my own right now!!!

  • Like 1

TM 2016 M2 12*(-2 setting) - OG Grafalloy Blue X, 43.5"

TEE XCG7 16.5* 4w, OG Grafalloy Blue S, 41.75"

Wilson D9 18* 4i, KBS Max-R, 39.5”

Cobra King OS 4-G, TT XP95 R300, -.5"

Vokey SM8 54.14F(2*weak), 60.10S(4*weak)

"Rusty" Byron DH89 Slant Pipe // Byron GSS DH89 Long Slant // GOAT NP2 Tiger Putter

Link to comment
Share on other sites

I’ve been thinking how I could make something similar....I take it you’re pulling the adapter by pulling a screw inserted into the end rather than wrecking the ferrule??

Ping G410 LST 9' Tour 65 Stiff
Callaway Epic Flash SZ #3 HZRDUS Smoke 6.0
Taylormade P790 #3 C-Taper 120 Stiff
Taylormade P770 4-5 C-Taper 120 Stiff
Taylormade P750 6-PW C-Taper 120 Stiff
Nike Engage 52' Square
Nike Engage 56' Square
Nike Engage 58' Dual Sole
Nike Engage 60' Toe Sweep
Taylormade Spider X Copper
Ping Anser Nickel
Ping DLX Cart / 4 Series White Tour Carry Bag

Link to comment
Share on other sites

39 minutes ago, nickosbad said:

I’ve been thinking how I could make something similar....I take it you’re pulling the adapter by pulling a screw inserted into the end rather than wrecking the ferrule??

Ya, I use a screw from the driver and a washer. Forgot to mention to put some tape on the shaft where it goes through the spreader, just to ensure the shaft doesn't get scratched.

Link to comment
Share on other sites

On 5/28/2021 at 3:38 PM, Fgav2402 said:

Just be sure to use a file to smooth out the metal after it has been cut, otherwise the shaft will get scratched

I forgot to ask. What size drill bit did you use and was there a specific place to drill that you found was best. 

It only hurts once, except golf it hurts a lifetime

Link to comment
Share on other sites

  • 2 months later...
On 8/2/2021 at 5:44 PM, Doaner84 said:

 @Fgav2402

On 8/2/2021 at 5:44 PM, Doaner84 said:

I finally got the chance to try it out and it works perfectly.  I grinded off the metal rod that turns the spreader and used a ratchet to turn it instead.  thax for the idea @Fgav2402

I'm glad it worked out for you. Its amazing what u can come up with when u are bored

 

Link to comment
Share on other sites

  • 3 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Our picks


×
×
  • Create New...