Tour Striker Pro 7i... what shaft is that?

[autronicdsm]

Bought a Tour Striker Pro and I've never hit an iron better than that. It has to be the shaft, since not even the good old Dynamic Gold is that good for me.

Does anyone know what shaft that is? Supposed to be True Temper Uniflex Steel. I really want to build a full set of irons with those

[ucmike11]

This may be similar:

https://www.grips4less.com/products/true-temper-commercial-grade-iron-steel-shaft-r-s-combo-0-370-parallel-tip

[Cwebb]

It could be this one...https://www.golfworks.com/tt-multi-step-lite-370-steel-iron-shaft/p/tt0186/

 

[autronicdsm]

28 minutes ago, ucmike11 said:

This may be similar:

https://www.grips4less.com/products/true-temper-commercial-grade-iron-steel-shaft-r-s-combo-0-370-parallel-tip

 

Winner winner chicken dinner. You might be right, it has the same label.

[autronicdsm]

22 minutes ago, Cwebb said:

It could be this one...https://www.golfworks.com/tt-multi-step-lite-370-steel-iron-shaft/p/tt0186/

 

 

Tour striker weighs 439g and my 7i with DG weighs 443g so I don't think it would be this. It's only 99g and you lose some weight after trimming it. The head would be 30g+ heavier in order to have 439g total weight. And swing weight does not feel heavy at all.

[Cwebb]

24 minutes ago, autronicdsm said:

 

Tour striker weighs 439g and my 7i with DG weighs 443g so I don't think it would be this. It's only 99g and you lose some weight after trimming it. The head would be 30g+ heavier in order to have 439g total weight. And swing weight does not feel heavy at all.

 

That would leave this option from True Temper...https://www.golfworks.com/true-temper-command-370-steel-iron-shafts/p/tt201103/

[autronicdsm]

18 minutes ago, Cwebb said:

 

That would leave this option from True Temper...https://www.golfworks.com/true-temper-command-370-steel-iron-shafts/p/tt201103/

 

Yeah I saw that earlier and was going to order it if I didn't get any replies here. I think @ucmike11 posted what I was after though. Spec weight is slightly different between the two.

Edited June 14 by autronicdsm

[Cwebb]

1 minute ago, autronicdsm said:

 

Yeah I saw that earlier and was going to order it if I didn't get any replies here. I think @ucmike11 posted what I was after though.

 

Might even be the same shafts with a different sticker.  Hard to imagine why they would produce (2) different "commercial grade" .370 R/S combo flex designs, that are stated to be that close in weight

[sigep1967]

pull the grip the model should be screen printed on the butt.

[Pnwpingi210]

You could reach out to true temper.  They are extremely responsive and helpful on items like this

[autronicdsm]

On 6/14/2024 at 3:38 PM, Cwebb said:

 

Might even be the same shafts with a different sticker.  Hard to imagine why they would produce (2) different "commercial grade" .370 R/S combo flex designs, that are stated to be that close in weight

 

Got the Command shafts from Golfworks today. Different step pattern than tour striker club  (but they sent red TT labels instead of Command 😞).

 

[Cwebb]

7 hours ago, autronicdsm said:

 

Got the Command shafts from Golfworks today. Different step pattern than tour striker club  (but they sent red TT labels instead of Command 😞).

 

 

Makes me wonder how close they would be in bend profile measurements.  Are you going to try one or send them back and order the others?

[autronicdsm]

1 hour ago, Cwebb said:

 

Makes me wonder how close they would be in bend profile measurements.  Are you going to try one or send them back and order the others?

 

Compared to DG S300, each step is just little bit longer.

I'll post a pic later.

[mizunoMP14]

maybe https://www.golfworks.com/true-temper-score-lt-steel-iron-shafts/p/tt0100/

[autronicdsm]

My second set came in and it's the same shaft as Golfworks Command one... SKU# UTIM-40 although some do not have anything printed on them.

Here's a pic of steps in case anyone cares. Top is tour striker shaft, starts off with two small steps. Middle shaft is TT "commercial" shaft. Bottom is DG S300.

Also I measured OD at various steps and tour striker is the biggest, about 1mm bigger than DG which explains why it felt better for me than DG.

Commercial shaft has smallest diameter and each step is the longest as well. 

 

I guess I'll reach out to TT to see if they can tell me.

 

[autronicdsm]

TT support got back to me and that "uniflex" shaft is discontinued. 

[Cwebb]

19 minutes ago, autronicdsm said:

TT support got back to me and that "uniflex" shaft is discontinued. 

 

Now I wonder if it was that old "Memphis 10" uniflex shaft that was made by True Temper for Callaway.

 

Does your shaft have two very small steps right below the grip, with the next step that is just over 4.25" long, followed by another very short 1/2" step?

[autronicdsm]

9 hours ago, Cwebb said:

 

Now I wonder if it was that old "Memphis 10" uniflex shaft that was made by True Temper for Callaway.

 

Does your shaft have two very small steps right below the grip, with the next step that is just over 4.25" long, followed by another very short 1/2" step?

 

No. First two steps are very short and the rest are 1-1.5" long.

 

I asked the guy what would be the closest match in their current lineup and he said Multi-Step, but those are 99g. I don't see how something 25g lighter could be similar.

[autronicdsm]

Ok, I should have done this earlier. Now I feel like an idiot lol

Started pulling end of the grip to see how long that step is and I realized there's no tape. I blew the grip off with a compressor and what do I see? The grip weighs a hefty 66g too! So much for the uniflex bs...

 

[Cwebb]

1 hour ago, autronicdsm said:

Ok, I should have done this earlier. Now I feel like an idiot lol

Started pulling end of the grip to see how long that step is and I realized there's no tape. I blew the grip off with a compressor and what do I see? The grip weighs a hefty 66g too! So much for the uniflex bs...

 

 

They put a competition grade red sticker on a DG 105?

[autronicdsm]

47 minutes ago, Cwebb said:

 

They put a competition grade red sticker on a DG 105?

 

I guess. Got me chasing unicorns and s***...

[autronicdsm]

Searched on ebay to see if I can find a good picture... steps on 105 do not look like the shaft I have. 

 

 

I'm going to ask TT customer service what that SKU is.

 

[EDIT] Found another set where it looks like the first two steps are short. wtf are there different version of DG105 or one of these are fake?😕

 

Edited Thursday at 05:02 AM by autronicdsm

[Cwebb]

35 minutes ago, autronicdsm said:

Searched on ebay to see if I can find a good picture... steps on 105 do not look like the shaft I have. 

 

 

I'm going to ask TT customer service what that SKU is.

 

[EDIT] Found another set where it looks like the first two steps are short. wtf are there different version of DG105 or one of these are fake?😕

 

 

 Keep in mind that those are likely .355 taper.  You stated that your shaft is a .370 tip.

 

With the DG lineup, the steps are usually different between .355 and .370 versions