Has my shaft been tipped? Shaft Measurements from raw tip to graphics

[Seamus_McDuff]

Pretty sure the shaft goes farther into the adapter than that. 
 

Edit - maybe I’m reading the ruler incorrectly

Edited February 12 by Seamus_McDuff

[third-times-a-charm]

32 minutes ago, Seamus_McDuff said:

Pretty sure the shaft goes farther into the adapter than that. 
 

Edit - maybe I’m reading the ruler incorrectly

You mean the shaft does not go into he adapter that far.

[third-times-a-charm]

1 hour ago, GQ0208 said:

I am measuring to the point in the adapter where the shaft ends and not the end of the adapter. Hence my concern of the 4.75”. 

You are not measuring it correctly the insertion depth into the adapter where it meets the ferrule should only be 1-1.25". That looks to be 1.5" in your pic.

 

 

[GQ0208]

17 minutes ago, third-times-a-charm said:

You are not measuring it correctly the insertion depth into the adapter where it meets the ferrule should only be 1-1.25". That looks to be 1.5" in your pic.

 

 

Thoughts looking at these pictures. 

[third-times-a-charm]

1 minute ago, GQ0208 said:

Thoughts looking at these pictures. 

Well, I said your measurement was off but i didnt say that a correct measurement would still be correct 😂

 

being 1/4" off still leaves you with 1/2" discrepancy if in fact the 4" on the hyb shaft is a correct raw measurement.

 

Either the shaft is not installed all the way down the adapter inside of it, Fujikura changed their graphics, or the shaft is fake.

 

Is the shaft an install by an OEM or done by a local shop with an aftermarket adapter?

[GQ0208]

8 minutes ago, third-times-a-charm said:

Well, I said your measurement was off but i didnt say that a correct measurement would still be correct 😂

 

being 1/4" off still leaves you with 1/2" discrepancy if in fact the 4" on the hyb shaft is a correct raw measurement.

 

Either the shaft is not installed all the way down the adapter inside of it, Fujikura changed their graphics, or the shaft is fake.

 

Is the shaft an install by an OEM or done by a local shop with an aftermarket adapter?

Haha. This sucks. I bought it off the bay and is definitely an aftermarket adapter. 

[third-times-a-charm]

1 minute ago, GQ0208 said:

Haha. This sucks. I bought it off the bay and is definitely an aftermarket adapter. 

The reason I am singling out an aftermarket adapter is because 8 times out of 10 I have to sand down the inside of the adapter with a reamer and/or sand off more than I normally do from a shaft tip to get them to fit on shafts all the way with the full 1-1.25" seating depth. It's possible whoever installed this adapter didnt seat the shaft all the way down and it's dangerously shallow in there. Even the buffoons at golf stores will mess this up.

 

I am a huge proponent of not using the $7 Amazon/Ebay chinesium adapters (OEM only even if it's a pull from a used OEM shaft) - some here claim the cheapies are just fine - but I've seen too many issues and differences with them.

 

YMMV.

 

Only way to see what's up is to pull the adapter IMO if you are 100% certain it's a real shaft first.

[GQ0208]

39 minutes ago, third-times-a-charm said:

The reason I am singling out an aftermarket adapter is because 8 times out of 10 I have to sand down the inside of the adapter with a reamer and/or sand off more than I normally do from a shaft tip to get them to fit on shafts all the way with the full 1-1.25" seating depth. It's possible whoever installed this adapter didnt seat the shaft all the way down and it's dangerously shallow in there. Even the buffoons at golf stores will mess this up.

 

I am a huge proponent of not using the $7 Amazon/Ebay chinesium adapters (OEM only even if it's a pull from a used OEM shaft) - some here claim the cheapies are just fine - but I've seen too many issues and differences with them.

 

YMMV.

 

Only way to see what's up is to pull the adapter IMO if you are 100% certain it's a real shaft first.

Thanks so much for your help. I was able to confirm with Fujikura that the hybrid is also 4” from the E. I suspect you are correct that it is installed very shallow.

[geochitown]

17 minutes ago, GQ0208 said:

Thanks so much for your help. I was able to confirm with Fujikura that the hybrid is also 4” from the E. I suspect you are correct that it is installed very shallow.

maybe tip weights were used?

 

 

[douglas2123]

Looking for the measurements for a Hzrdus Green Smoke (Taylormade issue) for raw tip to graphics. This is not the IMO or RDX version. Matte gray shaft, bright green graphics. Any help would be appreciated... even if you have one thats been tipped it would be a starting point for me. Thank you

Edited March 1 by douglas2123

[mjhuffer]

On 3/1/2024 at 11:32 AM, douglas2123 said:

Looking for the measurements for a Hzrdus Green Smoke (Taylormade issue) for raw tip to graphics. This is not the IMO or RDX version. Matte gray shaft, bright green graphics. Any help would be appreciated... even if you have one thats been tipped it would be a starting point for me. Thank you

If it is the same as the second gen smoke black it should be:

 

Project X Hzrdus Smoke Black (2nd Gen) - from tip to E in SMOKE is 20.25"

[MP-93]

On 7/9/2023 at 2:53 PM, third-times-a-charm said:

UST LIN-Q Purple - 22 7/8" from the tip to the silver smaller Lin-Q logo on the side of the shaft

 

@UST Mamiya Can you confirm this is the same for Lin-Q Black M40X 85?

[third-times-a-charm]

UNTIPPED tensei Av blue 2023 model 

 

the 2024 tensei 1k red is the same 

 

 

Edited May 4 by third-times-a-charm

[Bryanw99]

Anyone have a tip to graphics measurement for the UST Lin-q blue TSPX shaft?