Tour New adapter for putters with graphite shaft - 2023 Sanderson Farms

[GolfWRX_Spotted]

[getitdaily]

I see you kbs gps...I see you, snuggling up to my slant neck....getting all fresh and what-not.

[getitdaily]

Who makes the adapter?

[GolfWRX_Spotted]

7 hours ago, getitdaily said:

Who makes the adapter?

Bernie Garsen from Garsen grips is having them made.

 

 

 

Greg

Edited October 3 by pga43

[mackepa]

Absolutely love the concept but it just doesn’t look right. It would be too distracting for my eye at first. 

[newportbeach]

Interesting thanks for the pictures. Seems like a good idea. 

[Red4282]

Does it just screw on? What keeps it “locked” in place?

[granata10]

7 minutes ago, Red4282 said:

Does it just screw on? What keeps it “locked” in place?

It looks like the adapter is epoxied over the neck and then the shaft into the adapter!

[Red4282]

59 minutes ago, granata10 said:

It looks like the adapter is epoxied over the neck and then the shaft into the adapter!

If its epoxied to the head, whats the point of an adapter?

[D0ch0l1d4y]

3 minutes ago, Red4282 said:

If its epoxied to the head, whats the point of an adapter?

 

It's very difficult to install a graphite shaft on an over-the-hosel type putter, though LA golf did a one-off for DJ a few years ago.

That connector goes over the hosel then lets you install the graphite shaft like it's a socket hosel.

[chip75]

5 hours ago, getitdaily said:

Who makes the adapter?

 

5 hours ago, GolfWRX_Spotted said:

Bernier Garsen from Garsen grips is having them made.

 

 

 

Greg

I was going to say Home Depot, via the plumbing department.

 

Edited October 3 by chip75

[iNeedMoreGolf]

What is the benefit here other then a new look? Lol

[Red4282]

1 hour ago, D0ch0l1d4y said:

 

It's very difficult to install a graphite shaft on an over-the-hosel type putter, though LA golf did a one-off for DJ a few years ago.

That connector goes over the hosel then lets you install the graphite shaft like it's a socket hosel.

Ah makes sense now. Thanks

[getitdaily]

1 hour ago, iNeedMoreGolf said:

What is the benefit here other then a new look? Lol

Some graphite shafts will.only fit plumber's neck hosels. This allows this shafts to fit a slant neck.

 

Kbs gps for example 

[QuigleyDU]

Not the cleanest. But he is on to something.. the black on black is better.

Edited October 3 by QuigleyDU

[QuigleyDU]

I think it would look better if there were no rings and it was a smooth taper down instead of stepped.

[n_rones]

I like the concept wonder if someone will ever make something similar for double bend putters. Right now as far as aftermarket shafts go i believe you are limited to stability shafts for double bend putters.

[QuigleyDU]

1 hour ago, n_rones said:

I like the concept wonder if someone will ever make something similar for double bend putters. Right now as far as aftermarket shafts go i believe you are limited to stability shafts for double bend putters.

There is the UST all -IN shaft that you can use as well. There is a retro fit version with an adaptor. retrofit

[RangeBaller]

8 hours ago, n_rones said:

I like the concept wonder if someone will ever make something similar for double bend putters. Right now as far as aftermarket shafts go i believe you are limited to stability shafts for double bend putters.

My thoughts exactly.  I

Odyssey stroke lab double bend is the only thing I've seen that isn't full steel. I'll check out that UST all in 

[nosil]

1 hour ago, RangeBaller said:

My thoughts exactly.  I

Odyssey stroke lab double bend is the only thing I've seen that isn't full steel. I'll check out that UST all in 

 

You can also add the PXG shaft.  

[03trdblack]

Billy bobs has had a version of this out for a while. Not the best looking either but to each their own. 

 

 

Edited October 4 by pga43
No links allowed

[osubuckeyes691]

2 hours ago, nosil said:

 

You can also add the PXG shaft.  

Can you buy the M16 shaft separately?

[Tommyboi95]

On 10/2/2023 at 1:17 PM, getitdaily said:

Who makes the adapter?

DM me, it’s a guy in Nashville 

[Phabs]

Someone will eventually figure out how to make a nice one.  This one ain’t it for me 

[03trdblack]

On 10/4/2023 at 1:10 AM, Phabs said:

Someone will eventually figure out how to make a nice one.  This one ain’t it for me 

 

I think all you have to do is taper the edges so that it flows into the shaft like a ferrule on an iron. The hard edge is what's distracting. 

[Phabs]

12 minutes ago, 03trdblack said:

 

I think all you have to do is taper the edges so that it flows into the shaft like a ferrule on an iron. The hard edge is what's distracting. 

Correct.  If only i knew someone with cnc's and lots of aluminum haha 

[ForTourUseOnly]

Nippon needs to come out with a putter shaft with their GOST technology, they have the thinnest graphite layer on steel and it would be really cool.

 

This looks like too much going on down there.

[8384jeff]

On 10/3/2023 at 3:59 PM, 03trdblack said:

Billy bobs has had a version of this out for a while. Not the best looking either but to each their own. 

 

 

I can NOT thank you enough for this link, it's EXACTLY what I was looking for!  So much appreciated, 03, thanks again!  🙂  🙂  🙂 

[8384jeff]

A quick pic of the Billy Bob's golf adapter.